Ibm RS/6000 Bedienungsanleitung Seite 214
- Seite / 228
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Table 36 (Page 2 of 5). Firmware Checkpoint Three-Digit Codes
Code Description
F22 No memory found
F23 No DIMM found in the socket
F24 Remove bad DIMM found from DIMM information
F25 Unsupported DIMM detected
F26 Check valid image - start
F27 Check valid image - successful
F28 Wait for interrupt
F29 Transfers information to the business audio chip
F2B Wait till sound chip has been initialized
F2C Initialize the current input/pointer device
F2D Initialize the current output
F2E Register a console driver
F30 Set up early memory allocation heap, Initialize Super I/O
F31 Determine system bus speed, set ISA divisor
F32 Resync to SP (Composite Image)
F33 Set memory refresh
F35 Jump to set environment
F40 Initialize interrupt subsystem and 8259s
F41 SP command setup
F42 SP Mailbox interface
F43 get_vpd entry
F44 init_sp entry
F45 sp_recovery -> resync SP & CPU
F46 IRQ13 stuck high
F47 Entry to error checking routine
F48 Power Supply or System Board problem
F49 Voltage problem. System Board, Power Supply or CPU
F4A Voltage problem. System Board or Power Supply
F4B CPU over temperature or bad System Board
F4C Start bit-map display function
F4D Bit-map file read into memory, start processing
F4E End bit-map display function
F4F IO/MEM over temperature or bad System Board
F50 Initialize CMOS RTC periodic interrupt
F51 System Board or System over temperature
F52 Bad System Board (Fan Fail reported)
F53 Bad System Board
F54 Fan fail warning
190 Introduction to PCI-Based RS/6000 Servers
- April 1996 1
- First Edition (April 1996) 4
- Abstract 5
- Contents 7
- Special Notices 17
- Platform (CHRP) 19
- Related Publications 20
- Preface xix 21
- Acknowledgments 23
- Chapter 1. Introduction 25
- Chapter 1. Introduction 3 27
- Chapter 1. Introduction 5 29
- 1.3.3 PowerPC Platform Goals 31
- 1.3.4 CHRP Certification 32
- Architecture 33
- 2.1 The Hardware Design 35
- High Data Transfer Speed 37
- Processor Independence 37
- Cross-Platform Compatibility 37
- Multi-bus Support 38
- Plug and Play 38
- Investment protection 38
- 2.2.1 The Processor Subsystem 39
- 2.2.2 The L2 Cache 40
- 2.2.5 The Primary PCI Bus 41
- 2.2.4 The System Memory 41
- 2.2.6 The Secondary PCI Bus 42
- 2.2.7 The EISA Bus 42
- 2.2.8 The X-Bus 42
- 2.3 Electronics Partitioning 43
- 2.4.1 Standard Features 45
- Integrated SCSI-2 adapter 46
- Standard I/O ports 46
- 2.4.2.1 Internal Disk Drives 47
- 2.4.2.2 Internal Tape Drives 47
- 2.4.2.4 Graphics Adapter 48
- 2.4.2.5 PCI SCSI-2 Adapters 49
- PCI Ethernet Adapters 51
- 2.4.2.7 External Subsystems 54
- Internal Disk Drives 55
- Internal Tape Drives 55
- Graphics Adapter 55
- SCSI Adapters 55
- 2.5.1 Standard Features 56
- Integrated SCSI-2 Adapter 57
- 2.5.2.1 Internal Disk Drives 58
- 2.5.2.2 Internal Tape Drives 59
- 2.5.2.4 Graphics Adapter 59
- 2.5.2.5 PCI SCSI-2 Adapters 60
- 2.5.2.7 External Subsystems 61
- 2.6 Hardware Requirements 62
- 2.7 Performance Positioning 62
- SPEC base metrics 64
- SPEC rate metrics 64
- Chapter 3. Hot-Swap Subsystem 65
- 3.1.1 Backplanes 66
- 3.1.2 Hot-Swap Bays and Banks 67
- 3.2 Installation 68
- 3.2.5 Disk Carriers 70
- 3.3.4 Mirroring 74
- Managing 77
- 4.1 Boot Record 78
- 4.2.1 Firmware 80
- 4.2.2 Software ROS for AIX 80
- 4.3 Boot Image 82
- Name Description 83
- Base Proto Files: 84
- Proto Extension Files: 84
- 4.3.1.2 RAM File System 85
- Master Partition Header 86
- Reserved 1 86
- Reserved 2 86
- 4.4.1 Firmware Boot Sequence 89
- 4.4.2 Firmware Passwords 91
- 4.4.3 Firmware Flash Update 92
- 4.4.4 Firmware Recovery 93
- 4.4.5.3 Graphics Adapter POST 94
- 4.4.5.5 SCSI Subsystem POST 94
- 4.5 LCD Panel 95
- 4.6.1 SMS Graphical Main Menu 97
- 4.6.2 SMS ASCII Main Menu 97
- 4.6.3 Start-Up Menu 97
- 4.6.4 Test Menu 98
- 4.6.5 Tools Menu 98
- 5.1.1 Boot-Device Order List 99
- 5.1.3 bootlist Command 102
- 5.2 Entering Debug Mode 102
- 5.3 System Dump Support 103
- 5.3.4 Dump LCD Support 106
- 5.4 Managing System Backups 106
- 5.4.1 The bootinfo Command 107
- 5.4.6 Cloning 112
- 5.5 Configuration Information 114
- 5.6 Graphics Support 116
- 5.6.2 Resolution 118
- 5.6.3 Configuring the Adapter 118
- DISPLAY Variable Description 121
- RS/6000 Servers 123
- SG24-2581-00 124
- 6.1.2 Device Location Codes 125
- 6.2 PCI Adapter Configuration 126
- 6.3 ISA Adapter Configuration 128
- Figure 35. SMIT ISA Menu 131
- 6.4.1 DIP-Switch Setting 132
- 6.4.2 Configuring the Adapter 133
- 6.5.1 DIP-Switch Setting 136
- 6.5.2 Configuring the Adapter 136
- 6.6.2 DIP-Switch Setting 140
- 6.6.3 Configuring the Adapter 141
- Interrupt Level 142
- Bus I/O Address 142
- Bus Memory 142
- 6.7.1 DIP-Switch Setting 145
- 6.7.2 Configuring the Adapter 146
- System User's Guide 153
- Firmware Level 158
- Chapter 7. SCSI Cabling 161
- 7.1.2 SCSI Terminators 162
- 7.1.3 SCSI Device Addresses 162
- 7.1.4 SCSI Bus Width 162
- 8.2 Stand-Alone Diagnostics 172
- 8.3 Online Diagnostics 176
- 8.3.1 Concurrent Mode 176
- 8.3.2 Service Mode 177
- 8.3.3 Maintenance Mode 178
- Machine Object Name 179
- Operation to Perform 179
- Enable Diagnostics Boot 179
- 9.1 NIM Concepts 181
- 9.1.1 NIM Environment 181
- 9.1.2 NIM Objects 182
- 9.1.2.2 Network Objects 183
- 9.1.2.3 Machine Objects 183
- Network Install Route 184
- Gateway1 184
- Gateway2 184
- Network2 184
- 9.2.1 NIM Master Requirements 185
- 9.2.2 Filesystem Creation 185
- 9.2.3 NIM Master Activation 186
- Standalone1 187
- /inst.images 193
- Resource Object 194
- Chapter 10. Troubleshooting 203
- 10.2 Booting Problems 204
- 10.2.1 Booting From CD-ROM 204
- From this shell, you can 205
- 10.3 Installation Problems 206
- 10.3.2 NIM Installation 206
- 10.6.2.1 Power-On Password 208
- Figure 55. Operator Panel 210
- Table 35. LED Functions 210
- List of Abbreviations 219
- (continued) 223
- (continued) 223
- Name Address 225
- Company or Organization 225
- Phone No 225
- BUSINESS REPLY MAIL 226
- Printed in U.S.A 228
- SG24-469- 228
Verwandte Produkte und Handbücher für Computers Ibm RS/6000
Computers Ibm 6644 Bedienungsanleitung
(100 Seiten)
(100 Seiten)
Computers Ibm 1483DSV Bedienungsanleitung
(141 Seiten)
(141 Seiten)
Computers Ibm 47AE - 410168 Bedienungsanleitung
(27 Seiten)
(27 Seiten)
Computers Ibm 4190 Bedienungsanleitung
(84 Seiten)
(84 Seiten)
Computers Ibm GC09-2830-00 Bedienungsanleitung
(196 Seiten)
(196 Seiten)
Computers Ibm Novell 10 SP1 EAL4 Bedienungsanleitung
(246 Seiten)
(246 Seiten)
Computers Ibm A40 TYPE 6840 Bedienungsanleitung
(148 Seiten)
(148 Seiten)
Computers Ibm NETVISTA 6824 Bedienungsanleitung
(60 Seiten)
(60 Seiten)
Computers Ibm 440 Bedienungsanleitung
(202 Seiten)
(202 Seiten)
Computers Ibm GC23-7753-05 Bedienungsanleitung
(56 Seiten)
(56 Seiten)
Computers Ibm 610 Bedienungsanleitung
(40 Seiten)
(40 Seiten)
Computers Ibm NETVISTA X40 6643 Bedienungsanleitung
(120 Seiten)
(120 Seiten)
Computers Ibm POWER 730 Bedienungsanleitung
(45 Seiten)
(45 Seiten)
Computers Ibm 6648 Bedienungsanleitung
(248 Seiten)
(248 Seiten)
Computers Ibm 755 Bedienungsanleitung
(47 Seiten)
(47 Seiten)
Computers Ibm 170 Bedienungsanleitung
(18 Seiten)
(18 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.128 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern