IBM DS6000 Bedienungsanleitung Seite 282
- Seite / 406
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
258 DS6000 Series: Concepts and Architecture
target volumes in the new disk storage server. It can restart immediately to connect to the
new disk storage server after the XRC secondary volumes have been relabeled by a single
XRC command per XRC session, XRECOVER.
In addition to transparent data replication, the advantage for XRC is extreme scalability.
Figure 13-3 shows that XRC can run either in existing system images or in a dedicated LPAR.
Each image can host up to five System Data Movers (SDM). An SDM is an address space
(ANTAS00x) that is started by a respective XSTART command. A reasonable number of XRC
volume pairs which a single SDM can manage is in the range of 1,500 to 2,000 volume pairs.
With up to five SDMs within a system image, this totals approximately 10,000 volume pairs.
This requires an adequate bandwidth for the connectivity between the disk storage servers to
the system image which hosts the SDMs. Because XRC in migration mode stores the data
through, it mainly requires channel bandwidth and SDM tends to monopolize its channels.
Therefore, the approach with dedicated channel resources is an advantage over a shared
channel configuration and would almost not impact the application I/Os. In a medium sized
configuration, one or two SDMs is most likely sufficient.
Assume the migration consolidates two medium sized ESS F20s with a total of about 5 TB to
a DS6800 disk server. This would suggest connecting the SDM LPAR to each ESS F20 with
two dedicated ESCON channels. Configure for each F20 an SDM within the SDM LPAR. The
DS6800 FICON channels might be shared between the SDMs because there is no potential
bottleneck when coming from ESCON. This would take about one day to replicate all data
from the two F20s to the DS6800, provided there is not too much application write I/O during
the initial full copy. Otherwise it takes just a few more hours, depending on the amount of
application write I/O during the first full volume copy, and the entire migration can be
completed over a weekend.
XRC requires disk storage subsystems which support XRC primary volumes through the
microcode. Currently only IBM- or HDS-based controllers support XRC as a primary or
source disk subsystem. As an exception, this does not apply to the IBM RVA storage
controller, which does not support XRC as a primary XRC device. Also, EMC does not
provide XRC support at the XRC primary site.
13.2.3 Hardware- and microcode-based migration
Hardware- and microcode-based migration through remote copy is usually only possible
between like hardware, so using remote copy through microcode is not possible with different
disks from vendor A at the source site and disks from vendor B at the target site. Therefore,
we discuss only what is possible for IBM disk storage servers using remote copy or
Peer-to-Peer remote copy (PPRC) and its variations.
Remote copy approaches with Global Mirror, Metro Mirror, Metro/Global Copy, and Global
Copy allow the primary and secondary site to be any combination of ESS 750s, ESS 800s
and DS6000s or DS8000s.
Bridge from ESCON to FICON with Metro/Global Copy
The ESS Model E20 and Model F20 do not support PPRC over Fibre Channel links, but only
PPRC based on PPRC ESCON links. In contrast, the newly announced disk storage server
supports only PPRC over Fibre Channel links and does not support PPRC ESCON links. The
ESS Model 800 actually supports both PPRC link technologies.
- The IBM TotalStorage 1
- DS6000 Series: Concepts 1
- Contents ix 11
- LSS X'17' 100
- LSS X'18' 100
- DB2-test 100
- 4.2.7 Address groups 101
- 4.2.8 Volume access 101
- Host attachment 102
- Volume group 102
- 4.2.10 Placement of data 104
- Host LVM volume 105
- 5.1 DS6000 highlights 108
- 5.1.2 DS6000 Model 1750-EX1 109
- Loop 0) 111
- Loop 1) 111
- Controller 0 112
- Controller 1 112
- Copy Services 113
- 6.2 Copy Services functions 114
- Source Target 115
- 6.2.2 FlashCopy options 116
- Incremental FlashCopy 117
- Waiting write operation 119
- FlashCopy to 120
- PPRC Primary 120
- Persistent FlashCopy 121
- Global Copy (PPRC-XD) 122
- Server write 123
- Write to secondary 123
- (non-synchronously) 123
- Write acknowledge 123
- How Global Mirror works 124
- Global Mirror - How it works 125
- 127
Verwandte Produkte und Handbücher für Software IBM DS6000
Software IBM CDI5UG1107 Bedienungsanleitung
(178 Seiten)
(178 Seiten)
Software IBM GC28-1982-02 Bedienungsanleitung
(216 Seiten)
(216 Seiten)
Software IBM 12.1(22)EA6 Bedienungsanleitung
(550 Seiten)
(550 Seiten)
Whirlpool GE641TX manuály
Uživatelské manuály a uživatelské příručky pro Sporáky Whirlpool GE641TX.
Poskytujeme 1 manuály pdf Whirlpool GE641TX ke stažení zdarma podle typů dokumentů: Návod k použití
Kommentare zu diesen Handbüchern